 |
Nominal Frequency |
| Full size package: |
1.000MHz to 155.520MHz |
|
| Half size package: |
1.000MHz to 44.736MHz |
|
|
The specified reference or "center" frequency of the oscillator.
Typically specified in megahertz (MHz)or kilohertz (kHz).
|
|
Frequency Tolerance/Stability |
(Inclusive of all conditions: Calibration Tolerance at 25°C, Frequency Stability
over the Operating Temperature Range, Supply Voltage Change, Output Load Change,
First Year Aging at 25°C, Shock, and Vibration.)
±100ppm Maximum (Standard)
±50ppm Maximum
±25ppm Maximum
±20ppm Maximum (0°C to +70°C Only) |
|
This "inclusive" specification is the amount of frequency deviation
from the center frequency associated with a set of operating
conditions. These conditions include: Operating Temperature Range,
Supply Voltage, and Output Load. This parameter is specified with a
maximum and minimum frequency deviation, expressed in percent (%)
or parts per million (ppm).
|
|
Operating Temperature Range |
0°C to +70°C (Standard)
-40°C to +85°C |
|
The maximum and minimum temperatures that
the oscillator device can be exposed to during oscillation. Over this
temperature range, all of the specified device operating
parameters are guaranteed.
|
|
Supply Voltage (VDD) |
5.0VDC ±5% |
|
The DC input voltage necessary for oscillator operation, specified in
volts.
|
|
Input Current |
20mA Maximum from 1.544MHz to 20.000MHz
40mA Maximum from 20.000001MHz to 30.000MHz
50mA Maximum above 30.000MHz |
|
The amount of current consumption by an oscillator from the power
supply, typically specified in milliamps (mA).
|
|
Output Voltage Logic High (VOH) |
2.4VDC Minimum with TTL Load
VDD-0.5VDC Minimum with HCMOS Load |
|
Defined as the Output Voltage Logic High or "Logic 1"
(Figure 1 in oscillator
glossary of terms).
|
|
Output Voltage Logic Low (VOL) |
0.4VDC Maximum with TTL Load
0.5VDC Maximum with HCMOS Load |
|
Defined as the Output Voltage Logic Low or "Logic 0"
(Figure 1 in oscillator
glossary of terms).
|
|
Duty Cycle |
50 ±10(%) (Standard) measured at 1.4VDC with TTL Load or at 50% of waveform with HCMOS load.
50 ±5(%) (Optional) measured at 1.4VDC |
|
The measure of output waveform uniformity. This term, also referred
to as symmetry, is a measurement of the time that the output
waveform is in a logic high state, expressed as a percentage (%).
This parameter is measured at a specified voltage threshold or at a
percentage of the output waveform amplitude (Figure 1 in the oscillator glossary of terms).
|
|
Rise Time/Fall Time |
Measured over 0.4VDC to 2.4VDC with TTL load or from 20% to 80% of waveform with HCMOS load.
5nSec Maximum |
|
The Rise Time, measured in nanoseconds (nSec), is defined as the
transition time from an output logic low to an output logic high.
Conversely, the Fall Time, also measured in nanoseconds (nSec), is
defined as the transition time from an output logic high to an output
logic low. This transition time is measured at specified voltage
thresholds or at specified percentages of the output waveform
amplitude
(Figure 1 in the oscillator glossary of terms).
|
|
Load Drive Capability |
10 TTL or 15pF HCMOS Load Maximum |
|
The maximum load the oscillator can drive specified in terms of the
number of gates or the type of load circuit (Figures 2, 3 and 4 in oscillator glossary of terms).
|
|
Aging (at 25°C) |
±5ppm/year Maximum |
|
The systematic change in frequency with time due to internal changes in the crystal. Aging
is often expressed as a maximum value in parts per million per year (ppm/yr). The rate of
aging is typically greatest during the first 30 to 60 days after which time the aging rate
decreases. The following factors effect crystal aging: adsorption and desorption of
contamination on the surfaces of the quartz, stress relief of the mounting and bonding
structures, material outgassing, and seal integrity.
|
|
Storage Temperature |
-55°C to +125°C |
|
The minimum and maximum temperatures that the device can
be stored or exposed to when in a non-oscillation state. After exposing or
storing the device at the minimum or maximum temperatures for a length of
time, all of the operating specifications are guaranteed over the specified
Operating Temperature Range.
|
|
| Control Voltage (Pin 1) |
2.5VDC ±2.0VDC Positive Transfer Characteristic or
2.5VDC ±2.5VDC Positive Transfer Characteristic (with
frequency deviation of ±200ppm only) |
|
| Frequency Deviation over Control Voltage |
±50ppm Minimum
±100ppm Minimum
±150ppm Minimum
±200ppm Minimum (Full Size Only) |
|
| Jitter |
| Frequency Deviation of ±50ppm, ±100ppm & ±150ppm: |
<44.736MHz |
Absolute: ±100pSec Maximum
One Sigma: ±25pSec Maximum
|
| |
>44.736MHz |
Absolute: ±200pSec Maximum
One Sigma: ±50pSec Maximum
|
|
| Frequency Deviation of ±200ppm: |
<30MHz |
Absolute: ±100pSec Maximum
One Sigma: ±25pSec Maximum
|
| |
>30MHz |
Absolute: ±200pSec Maximum
One Sigma: ±50pSec Maximum
|
|
|
Start Up Time |
10mSec Maximum |
|
The specified time from oscillator power-up to the time the oscillator
reaches steady state oscillation.
|
|
| Linearity |
±20% Maximum
±15% Maximum
±10% Maximum
±5% Maximum (not available with ±200ppm Frequency Deviation) |
|
Check Stock
Mechanical Dimensions
Part Number Constructor / Request a Quote or Sample
Marking Specifications
Environmental & Mechanical Specifications
Other Resources