 |
Nominal Frequency |
1.000MHz to 106.250MHz |
|
The specified reference or "center" frequency of the oscillator.
Typically specified in megahertz (MHz)or kilohertz (kHz).
|
|
Frequency Tolerance/Stability |
(Inclusive of all conditions: Calibration Tolerance at 25°C, Frequency Stability over the Operating Temperature Range,
Supply Voltage Change, Output Load Change, First Year Aging at 25°C, 260° Reflow, Shock and Vibration)
±50ppm Maximum |
|
This "inclusive" specification is the amount of frequency deviation
from the center frequency associated with a set of operating
conditions. These conditions include: Operating Temperature Range,
Supply Voltage, and Output Load. This parameter is specified with a
maximum and minimum frequency deviation, expressed in percent (%)
or parts per million (ppm).
|
|
Operating Temperature Range |
-20°C to +70°C
-40°C to +85°C |
|
The maximum and minimum temperatures that
the oscillator device can be exposed to during oscillation. Over this
temperature range, all of the specified device operating
parameters are guaranteed.
|
|
Supply Voltage (VDD) |
2.5VDC ±5% |
|
The DC input voltage necessary for oscillator operation, specified in
volts.
|
|
Input Current |
13mA Maximum |
|
The amount of current consumption by an oscillator from the power
supply, typically specified in milliamps (mA).
|
|
Output Voltage Logic High (VOH) |
90% of VDD Minimum (IOH=-4mA) |
|
Defined as the Output Voltage Logic High or "Logic 1"
(Figure 1 in oscillator
glossary of terms).
|
|
Output Voltage Logic Low (VOL) |
10% of VDD Maximum (IOL=+4mA) |
|
Defined as the Output Voltage Logic Low or "Logic 0"
(Figure 1 in oscillator
glossary of terms).
|
|
Duty Cycle |
Measured at 50% of waveform
50 ±5(%) over Nominal Frequency of 1.000MHz to 79.999999MHz
50 ±10(%) over Nominal Frequency of 80.000MHz to 106.250MHz
|
|
The measure of output waveform uniformity. This term, also referred
to as symmetry, is a measurement of the time that the output
waveform is in a logic high state, expressed as a percentage (%).
This parameter is measured at a specified voltage threshold or at a
percentage of the output waveform amplitude (Figure 1 in the oscillator glossary of terms).
|
|
Rise Time/Fall Time |
Measured from 20% to 80% of waveform
2nSec Maximum |
|
The Rise Time, measured in nanoseconds (nSec), is defined as the
transition time from an output logic low to an output logic high.
Conversely, the Fall Time, also measured in nanoseconds (nSec), is
defined as the transition time from an output logic high to an output
logic low. This transition time is measured at specified voltage
thresholds or at specified percentages of the output waveform
amplitude
(Figure 1 in the oscillator glossary of terms).
|
|
Load Drive Capability |
15pF Maximum |
|
The maximum load the oscillator can drive specified in terms of the
number of gates or the type of load circuit (Figures 2, 3 and 4 in oscillator glossary of terms).
|
|
| Absolute Pull Range |
Inclusive of all conditions: Calibration Tolerance at 25°C, Frequency Stability over the Operating Temperature Range,
Supply Voltage Change, Output Load Change, Shock, Vibration, and First Year Aging at 25°C over the Control Voltage
(Vc).
±30ppm Minimum
±50ppm Minimum
±80ppm Minimum
±100ppm Minimum |
|
| Control Voltage |
Test Condition for APR
0.05Vdc to 1.7Vdc |
|
| Control Voltage Range |
0.0Vdc to 1.8Vdc |
|
| Linearity |
1% Maximum |
|
| Transfer Function |
Positive Transfer Characteristic |
|
| Modulation Bandwidth |
Measured at -3dB, Vc = 0.875Vdc
8kHz Typical, 5kHz Minimum |
|
| Input Impedance |
250kOhms Minimum |
|
| Input Leakage Current |
10µA Maximum |
|
| Typical Phase Noise at Offsets |
-100dBc/Hz at offset of 10kHz
-115dBc/Hz at offset of 100kHz
-145dBc/Hz at offset of 1MHz
-154dBc/Hz at offset of 10MHz
|
|
| Period Jitter (RMS) |
3pSec Typical, 6pSec Maximum |
|
| Period Jitter (pk-pk) |
20pSec Typical, 40pSec Maximum |
|
| RMS Phase Jitter |
Fj=900kHz to 7.5MHz; Random
0.6pSec Typical |
|
| RMS Phase Jitter |
Fj=1.875MHz to 20MHz; Random
0.8pSec Typical |
|
Start Up Time |
10mSec Maximum |
|
The specified time from oscillator power-up to the time the oscillator
reaches steady state oscillation.
|
|
Storage Temperature |
-55°C to +125°C |
|
The minimum and maximum temperatures that the device can
be stored or exposed to when in a non-oscillation state. After exposing or
storing the device at the minimum or maximum temperatures for a length of
time, all of the operating specifications are guaranteed over the specified
Operating Temperature Range.
|
|
Stock Search
Mechanical Dimensions
Part Number Constructor / Request a Quote or Sample
Marking Specifications
Environmental & Mechanical Specifications
Other Resources