 |
Nominal Frequency |
77.760MHz, 78.125MHz, 80.000MHz, 80.157MHz, 85.000MHz, 87.125MHz,
90.000MHz, 100.000MHz, 106.250MHz, 110.000MHz, 119.000MHz, 120.000MHz, 122.888MHz,
124.400MHz, 125.000MHz, 127.000MHz, 128.000MHz, 133.000MHz, 133.333MHz,
137.472MHz, 150.000MHz, 155.520MHz, 156.250MHz, 159.375MHz, 161.1328MHz, 162.500MHz,
166.000MHz, 170.000MHz, 175.000MHz, 176.83816MHz, 187.500MHz, 187.509375MHz 200.000MHz, or 212.500MHz
|
|
The specified reference or "center" frequency of the oscillator.
Typically specified in megahertz (MHz)or kilohertz (kHz).
|
|
| Frequency Tolerance/Stability |
Inclusive of all conditions: Calibration Tolerance at 25°C, Frequency Stability over the
Operating Temperature Range, Supply Voltage Change, Output Load Change, 1st Year Aging at 25°C,
Shock, and Vibration
±100ppm Maximum
±50ppm Maximum
±25ppm Maximum |
|
Operating Temperature Range |
0°C to +70°C
-40°C to +85°C(The ±25ppm Frequency Tolerance/Stability option is not available for Nominal Frequencies greater than 175.000MHz) |
|
The maximum and minimum temperatures that
the oscillator device can be exposed to during oscillation. Over this
temperature range, all of the specified device operating
parameters are guaranteed.
|
|
Supply Voltage (VCC) |
2.5VDC ±5% |
|
The DC input voltage necessary for oscillator operation, specified in
volts.
|
|
Input Current (with Load) |
75mA Maximum |
|
The amount of current consumption by an oscillator from the power
supply, typically specified in milliamps (mA).
|
|
Output Voltage Logic High (VOH) |
VCC-1.025VDC Minimum from 0°C to +85°C
VCC-1.085VDC Minimum from -40°C to 0°C
|
|
Defined as the Output Voltage Logic High or "Logic 1"
(Figure 1 in oscillator
glossary of terms).
|
|
Output Voltage Logic Low (VOL) |
VCC-1.405VDC Maximum from 0°C to +85°C
VCC-1.305VDC Maximum from -40°C to 0°C
|
|
Defined as the Output Voltage Logic Low or "Logic 0"
(Figure 1 in oscillator
glossary of terms).
|
|
Duty Cycle |
Measured at 50% of waveform
50 ±5(%) |
|
The measure of output waveform uniformity. This term, also referred
to as symmetry, is a measurement of the time that the output
waveform is in a logic high state, expressed as a percentage (%).
This parameter is measured at a specified voltage threshold or at a
percentage of the output waveform amplitude (Figure 1 in the oscillator glossary of terms).
|
|
Rise Time/Fall Time |
Measured over 20% to 80% of waveform
300pSec Typical, 700pSec Maximum |
|
The Rise Time, measured in nanoseconds (nSec), is defined as the
transition time from an output logic low to an output logic high.
Conversely, the Fall Time, also measured in nanoseconds (nSec), is
defined as the transition time from an output logic high to an output
logic low. This transition time is measured at specified voltage
thresholds or at specified percentages of the output waveform
amplitude
(Figure 1 in the oscillator glossary of terms).
|
|
| Load Drive Capability |
50 Ohms into VCC-2.0VDC |
|
Storage Temperature |
-55°C to +125°C |
|
The minimum and maximum temperatures that the device can
be stored or exposed to when in a non-oscillation state. After exposing or
storing the device at the minimum or maximum temperatures for a length of
time, all of the operating specifications are guaranteed over the specified
Operating Temperature Range.
|
|
| Logic Control / Additional Output |
Tri-State (High Impedance) / Complementary Output |
|
| Tri-State Input Voltage |
VIH of 70% of VCC Minimum or No
Connect to Enable Output and Complementary Output, VIL
of 30% of VCC Maximum to Disable Output and
Complementary Output (High Impedance). |
|
| Start-Up Time |
10mSec Maximum |
|
| RMS Phase Jitter |
FJ=12kHz to 20MHz
0.4pSec Typical, 1pSec Maximum
|
|
| Standby Current (Without Load) |
30µA Maximum |
|
| Typical Phase Noise |
FO = 156.250MHz
-60dBc/Hz at 10Hz Offset
-95dBc/Hz at 100Hz Offset
-125dBc/Hz at 1kHz Offset
-143dBc/Hz at 10kHz Offset
-145dBc/Hz at 100kHz Offset
-145dBc/Hz at 1MHz Offset
-146dBc/Hz at 10MHz Offset
|
|
Check Stock
Mechanical Dimensions
Part Number Constructor / Request a Quote or Sample
Marking Specifications
Environmental & Mechanical Specifications
Other Resources