 |
Nominal Frequency |
6.000MHz, 6.144MHz, 6.400MHz, 6.500MHz, 8.000MHz, 8.192MHz, 9.216MHz, 9.600MHz, 9.720MHz,
10.000MHz, 12.000MHz, 12.288MHz, 12.800MHz, 13.000MHz or 14.400MHz
|
|
The specified reference or "center" frequency of the oscillator.
Typically specified in megahertz (MHz)or kilohertz (kHz).
|
|
| Frequency Stability |
| vs. Operating Temperature Range(VDD=3.3VDC,VC=1.65VDC±(Fmax - Fmin)/2 Fo): |
±0.5ppm Maximum
(-20°C to 70°C only)
±1.0ppm Maximum
±1.5ppm Maximum
±2.0ppm Maximum
±2.5ppm Maximum
|
|
| vs. Frequency Tolerance (25°C ±2°C, VDD=3.3VDC, VC=1.65VDC): |
±1.0ppm Maximum |
|
| vs. Input Voltage (±5%): |
±0.3ppm Maximum |
|
| vs. Load (±10%): |
±0.3ppm Maximum |
|
| vs. Aging (at 25°C): |
±1.0ppm/year Maximum |
|
|
Operating Temperature Range |
-20°C to 70°C
-40°C to 85°C
|
|
The maximum and minimum temperatures that
the oscillator device can be exposed to during oscillation. Over this
temperature range, all of the specified device operating
parameters are guaranteed.
|
|
Supply Voltage (VDD) |
3.3VDC ±5% |
|
The DC input voltage necessary for oscillator operation, specified in
volts.
|
|
Input Current |
10mA Maximum
|
|
The amount of current consumption by an oscillator from the power
supply, typically specified in milliamps (mA).
|
|
Output Voltage Logic High (VOH) |
IOH = -4mA
90% of VDD Minimum
|
|
Output Voltage Logic Low (VOL) |
IOL = +4mA
10% of VDD Maximum
|
|
Defined as the Output Voltage Logic Low or "Logic 0"
(Figure 1 in oscillator
glossary of terms).
|
|
Rise Time/Fall Time |
Measured at 20% to 80% of waveform
5nSec Maximum |
|
The Rise Time, measured in nanoseconds (nSec), is defined as the
transition time from an output logic low to an output logic high.
Conversely, the Fall Time, also measured in nanoseconds (nSec), is
defined as the transition time from an output logic high to an output
logic low. This transition time is measured at specified voltage
thresholds or at specified percentages of the output waveform
amplitude
(Figure 1 in the oscillator glossary of terms).
|
|
Duty Cycle |
Measured at 50% of waveform
50 ±5(%) |
|
The measure of output waveform uniformity. This term, also referred
to as symmetry, is a measurement of the time that the output
waveform is in a logic high state, expressed as a percentage (%).
This parameter is measured at a specified voltage threshold or at a
percentage of the output waveform amplitude (Figure 1 in the oscillator glossary of terms).
|
|
Load Drive Capability |
15pF HCMOS Load |
|
The maximum load the oscillator can drive specified in terms of the
number of gates or the type of load circuit (Figures 2, 3 and 4 in oscillator glossary of terms).
|
|
| External Trim(Voltage Control Option) |
1.65VDC±1.65VDC; Positive Transfer Characteristic ±5ppm Minimum |
|
Defined as the Output Voltage Logic Low or "Logic 0"
(Figure 1 in oscillator
glossary of terms).
|
|
| Control Voltage Range |
0.0VDCto VDD |
|
| Linearity |
5% Maximum |
|
| Input Impedance |
100kOhms Minimum |
|
| Typical Phase Noise |
Measured at 12.800MHz
-80dBc/Hz Typical at 10Hz Offset
-115dBc/Hz Typical at 100Hz Offset
-135dBc/Hz Typical at 1kHz Offset
-145dBc/Hz Typical at 10kHz Offset
|
|
| Tri-State Input Voltage (VIH and VIL) |
+0.9VDD Minimum to Enable Output
+0.1 VDD Maximum to Disable Output(High Impedance)
No Connect to Enable Output |
|
| RMS Phase Jitter |
FJ = 12kHz to 20MHz
1pSec Maximum |
|
| Start Up Time |
5mSec Maximum |
|
Storage Temperature |
-40°C to +125°C |
|
The minimum and maximum temperatures that the device can
be stored or exposed to when in a non-oscillation state. After exposing or
storing the device at the minimum or maximum temperatures for a length of
time, all of the operating specifications are guaranteed over the specified
Operating Temperature Range.
|
|
Check Stock
Mechanical Dimensions
Part Number Constructor / Request a Quote or Sample
Marking Specifications
Environmental & Mechanical Specifications
Other Resources